Dell S4248FB-ON Installation Manual Download Page 41

Page: 41 / 47

Specifications

This section lists the S4200-ON Series (S4248FB-ON and S4248FBL-ON) switch specifications.

CAUTION:

Operate the product at an ambient temperature not higher than 113°F—45°C.

CAUTION:

Lithium Battery Caution: There is a danger of explosion if the battery is incorrectly replaced. Replace only with same

or equivalent type of battery. Dispose of the batteries according to the manufacturer's instructions.

NOTE:

For RoHS information, see

Restricted Material Compliance

Topics:

•

Chassis physical design

•

IEEE standards

•

Agency compliance

•

USA Federal Communications Commission statement

•

European Union EMC directive conformance statement

•

Japan VCCI compliance for class A equipment

•

Korean certification of compliance

•

Electromagnetic compatibility

•

Safety standards and compliance agency certifications

•

Product recycling and disposal

Chassis physical design

Table 5. Chassis physical design

Parameter

Specifications

Height

1.72 inches (44 mm)

Width

17.1 inches (434 mm)

Depth

18.2 inches (462 mm)

PSU/fan tray handle: 1.57 inches (40 mm)

Chassis weight with factory-installed components

22 lbs (2* PSUs)

9.98 kg (2* PSUs)

Rack clearance required

Front: 5 inches (12.7 cm)

Back: 5 inches (12.7 cm)

Specifications

Summary of Contents for S4248FB-ON
















































Search results

Summary of Contents for S4248FB-ON

Reviews:

Related manuals for S4248FB-ON

Brands by name

Popular brands

Dell S4248FB-ON, Installation Manual

Search results

Summary of Contents for S4248FB-ON

Reviews:

Related manuals for S4248FB-ON

Brands by name

Popular brands