Dell S4248FB-ON Installation Manual Download Page 3

Page: 3 / 47

Contents

1 About this guide............................................................................................................................................. 5

2 S4200-ON series switch................................................................................................................................ 7

LED behavior................................................................................................................................................................ 9

3 Site preparations.......................................................................................................................................... 13

Fan combinations........................................................................................................................................................14

Power................................................................................................................................................................................. 14
Component storage..........................................................................................................................................................15

4 NEBS compliance.........................................................................................................................................16

Important information...................................................................................................................................................... 16
NEBS-compliant ground installation...............................................................................................................................16

5 S4200-ON Series installation....................................................................................................................... 19

Unpack the switch............................................................................................................................................................19

Unpack......................................................................................................................................................................... 19

Rack or cabinet installation.............................................................................................................................................20

Rack mount safety considerations...........................................................................................................................20

ReadyRails Installation..................................................................................................................................................... 20

S4200-ON Series switch installation.............................................................................................................................25

1U front-rack installation........................................................................................................................................... 25

Ground cable.....................................................................................................................................................................27

Contents

Summary of Contents for S4248FB-ON
















































Search results

Summary of Contents for S4248FB-ON

Reviews:

Related manuals for S4248FB-ON

Brands by name

Popular brands

Dell S4248FB-ON, Installation Manual

Search results

Summary of Contents for S4248FB-ON

Reviews:

Related manuals for S4248FB-ON

Brands by name

Popular brands