manualshive.com logo in svg

Dell Precision M6600, Owner'S Manual

Share
Download
Dell Precision M6600 Owner'S Manual Download Page 132

Device Status Lights

Turns on when you turn on the computer
and blinks when the computer is in a
power management mode.

Turns on when the computer reads or
writes data.

Turns on steadily or blinks to indicate
battery charge status.

Turns on when wireless networking is
enabled.

Turns on when a card with Bluetooth
wireless technology is enabled. To turn off
only the Bluetooth wireless technology
function, right-click the icon in the system
tray and select Disable Bluetooth Radio.

Battery Status Lights
If the computer is connected to an electrical outlet, the battery light operates as

follows:

• Alternately blinking amber light and blue light — An unauthenticated or

unsupported non-Dell AC adapter is attached to your laptop.

• Alternately blinking amber light with steady blue light — Temporary battery

failure with AC adapter present.

• Constantly blinking amber light — Fatal battery failure with AC adapter

present.

• Light off — Battery in full charge mode with AC adapter present.
• Blue light on — Battery in charge mode with AC adapter present.

LED Error Codes
The following table shows the possible LED codes that may display when your

computer is unable to complete a power on self test.

Diagnostic LED

Error Description

HDD/

Storage

LED

Battery

LED

Wireless

LED

132

Summary of Contents for Precision M6600









































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands