Dell PowerVault 500, Owner'S Manual

Page: 6 / 86

LCD Status Messages
The system's control panel LCD provides status messages to signify when the system is operating correctly or when the system needs attention.
The LCD lights blue to indicate a normal operating condition, and lights amber to indicate an error condition. The LCD scrolls a message that includes a status
code followed by descriptive text.
Table 1 -6 lists the LCD status messages that can occur and the probable cause for each message. The LCD messages refer
to events recorded in the System Event Log (SEL). For information on the SEL and configuring system management settings, see the systems management
software documentation.
Table 1- 6. LCD Status Messages
Link and activity indicators are off The NIC is not connected to the network.
Link indicator is green The NIC is connected to a valid link partner on the network.
Activity indicator is amber blinking Network data is being sent or received.
CAUTION: Only trained service technicians are authorized to remove the system cover and access any of the components inside the system. See
your Product Information Guide for complete information about safety precautions, working inside the computer, and protecting against
electrostatic discharge.
NOTE: If your system fails to boot, press the System ID button for at least five seconds until an error code appears on the LCD. Record the code, then
see Getting Help .
Code Text Causes Corrective Actions
N/A SYSTEM NAME
A 62-character string that can be defined by the user in the
System Setup program.
The SYSTEM NAME displays under the following conditions:
l
The system is powered on.
l
The power is off and active POST errors are
displayed.
This message is for information only.
You can change the system ID and name in the System Setup
program. See
Using the System Setup Program .
E1000 FAILSAFE,
Call Support
See Getting Help .
E1114 Temp Ambient
Ambient system temperature is out of acceptable range. See Troubleshooting System Cooling Problems .
E1116 Temp Memory
Memory has exceeded acceptable temperature and has
been disabled to prevent damage to the components. See Troubleshooting System Cooling Problems .
E12 nn xx PwrGd
Specified voltage regulator has failed. See Getting Help .
E1210 CMOS Batt
CMOS battery is missing, or the voltage is out of acceptable
range. See Troubleshooting the System Battery .
E1211 ROMB Batt
RAID battery is either missing, bad, or unable to recharge
due to thermal issues. Reseat the RAID battery connector. See RAID Battery , and
Troubleshooting System Cooling Problems .
E1229 CPU # VCORE
Processor # VCORE voltage regulator has failed. See Getting Help .
E1310 RPM Fan ##
RPM of specified cooling fan is out of acceptable operating
range. See Troubleshooting System Cooling Problems .
E1313 Fan
Redundancy
The system is no longer fan-redundant. Another fan failure
will put the system at risk of over-heating. Check control panel LCD for additional scrolling messages. See
Troubleshooting System Cooling Problems .
E1410 CPU # IERR
Specified microprocessor is reporting an internal error. See your system's Information Update Tech Sheet located on
support.dell.com for the most current system information. If problem
persists, see Getting Help .
E1414 CPU #
Thermtrip
Specified microprocessor is out of acceptable temperature
range and has halted operation. See Troubleshooting System Cooling Problems . If the problem persists,
ensure that the microprocessor heat sinks are properly installed. See
Troubleshooting the Microprocessors .
NOTE: The LCD continues to display this message until the system's
power cord is disconnected and reconnected to the AC power source,
or the SEL is cleared using either Server Assistant or the BMC
Management Utility. See the
Dell OpenManage Baseboard Management
Controller User's Guide for information about these utilities.
E1418 CPU #
Presence
Specified processor is missing or bad, and the system is in
an unsupported configuration. See Troubleshooting the Microprocessors .
E141C CPU Mismatch
Processors are in a configuration unsupported by Dell. Ensure that your processors match and conform to the type described
in the Microprocessor Technical Specifications outlined in your system's
Getting Started Guide .
E141F CPU Protocol
The system BIOS has reported a processor protocol error. See Getting Help .
E1420 CPU Bus PERR
The system BIOS has reported a processor bus parity error. See Getting Help .
E1421 CPU Init
The system BIOS has reported a processor initialization
error. See Getting Help .
E1422 CPU Machine
Chk
The system BIOS has reported a machine check error. See Getting Help .