Dell OptiPlex Gs Reference And Installation Manual Download Page 93 | Manualshive

Page: 93 / 121

background image

Installing Drives

7-13

9.

If you installed a SCSI hard-disk drive, replace
the expansion-card cage as instructed in
“Replacing the Expansion-Card Cage” in
Chapter 5.

10. Replace the computer cover. Then reconnect your

computer and peripherals to their power sources,
and turn them on.

11. If necessary, enter the System Setup program to

update the system configuration information.

If you installed a SCSI hard-disk drive, set the

DRIVE

0

and

DRIVE

1

System Setup categories under

DRIVES:

PRIMARY

to

NONE

. For instructions, see Chapter 2,

“Using the System Setup Program.”

Tape drives attached to a SCSI host adapter card are
not part of the system configuration information.

12. If you installed a SCSI hard-disk drive, partition

and format the drive. Then install the operating
system.

See your operating system documentation for
instructions as well as the next subsection, “Parti-
tioning and Formatting SCSI Hard-Disk Drives.”

13. Test the SCSI devices.

Test a SCSI hard-disk drive by running the SCSI
Test Group of the Dell diagnostics. See your
Diagnostics and Troubleshooting Guide for
information on running the diskette-based
diagnostics and troubleshooting any problems that
may occur.

To test a SCSI tape drive, refer to the documentation
for the tape drive software to perform a tape drive
backup and verification test.

Partitioning and Formatting SCSI
Hard-Disk Drives

You may need to use different programs than those pro-
vided with the operating system to partition and format
SCSI hard-disk drives. Refer to the documentation that
came with your SCSI software drivers for information on
installing the appropriate drivers and preparing your
SCSI hard-disk drive for use.

NOTE: On systems with hard-disk drives larger than
2 GB, create a primary partition of 2 GB and divide the
remaining capacity into partitions of 2 GB or less. For
example, a system with a 2.5-GB hard-disk drive would
have a primary partition of 2 GB (drive C) and a second
partition of 500 MB (drive D). Hard-disk drives must be
partitioned this way because MS-DOS–based operating
systems (including Windows NT when using a FAT16 file
system) do not support drive partitions larger than 2 GB.

93816BK0.BK : 93816c70.frm Page 13 Monday, September 16, 1996 1:21 PM

«
...
91
92
93
94
95
...
»

Summary of Contents for OptiPlex Gs


























































































































Reviews:

No comments

Related manuals for OptiPlex Gs

Brand: Panasonic Pages: 15

Brand: Acer Pages: 25

HC10 - BladeCenter - 7996

Brand: IBM Pages: 114

Brand: Yawarra Pages: 4

Brand: IBM Pages: 75

Aqua Compact Pro

Brand: DIGITAL YACHT Pages: 5

Brand: Prentke Romich Company Pages: 36

Brand: Acer Pages: 74

Brand: Acer Pages: 83

Brand: Acer Pages: 77

Brand: Acer Pages: 97

Brand: Acer Pages: 73

Brand: Acer Pages: 28

Brand: Acer Pages: 105

Brand: Acer Pages: 98

Brand: Acer Pages: 30

Brand: Acer Pages: 52

Brand: Acer Pages: 101

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands