Dell Networking N4032 Configuration Manual Download Page 39 | Manualshive

Page: 39 / 60

background image

39

Stacking Dell Networking Switches: N4032, N4032F, N4064, N4064F

2.5

Removing member units

This section provides guidance on how to remove member units from a stack while minimizing traffic flow
interruptions within the stack. Removing any member of a

ring topology

stack does not require a reload

of any member unit in the stack.

If a unit in the stack fails, the Master unit removes the failed unit from the stack and no changes or
configuration are applied to the other stack members; however, the dynamic protocols will try to re-
converge as the topology could change because of the failed unit. When there are no connected ports on
the failed unit, the stack will be intact without changes. The example below demonstrates how to
manually remove a single member while keeping the stack intact.

Run the show switch command to see the current Stack configuration. For this example Unit 2 will be
removed.

console#

show switch

  Management Standby Preconfig Plugged-in Switch Code
SW Status Status Model ID Model ID    Status Version
--- ---------- --------- ------------- ------------- ------------- --------
1 Mgmt Sw N4032 N4032 OK 6.0.1.3
2 Stack Mbr Oper Stby N4032F N4032F OK 6.0.1.3
3 Stack Mbr N4064 N4064 OK 6.0.1.3

2.5.1

Command-line interface method

Since any interface on these switches can be used for stacking, make sure to verify exactly which ports are
being used for stacking so they are un-cabled and re-routed last. This information is found with the
following command.

console#

show switch stack-ports | include Stack

Interface Stack Mode Stack Mode Status Speed (Gb/s) Status
Te1/0/7 Stack Stack Link Up 10 Enabled
Te1/0/8 Stack Stack Link Up 10 Enabled
Te2/1/1 Stack Stack Link Up 10 Enabled
Te2/1/2 Stack Stack Link Up 10 Enabled
Te3/0/7 Stack Stack Link Up 10 Enabled
Te3/0/8 Stack Stack Link Up 10 Enabled

Note:

Be sure to capitalize

Stack

since the command is case sensitive.

Only interfaces in Stack mode are displayed. The logical stack unit number is represented in each
interface name. The first number in the interface name is the logical stack unit. For example, interface
Te

2

/1/1 is in logical unit number 2.

A blinking LED light can be generated on the

back

of each Dell N4xxx to locate each physical unit. This

blinking LED is useful when identifying physical units and ports for running diags, sniffing, mirroring ports,
and other basic troubleshooting. It is also helpful when adding, removing, replacing or tracing cables

«
...
37
38
39
40
41
...
»

Summary of Contents for Networking N4032





























































Reviews:

No comments

Related manuals for Networking N4032

Brand: JDS Uniphase Pages: 40

Brand: D-Link Pages: 16

Brand: D-Link Pages: 2

Brand: OFFICINE OROBICHE Pages: 7

Brand: Jabra Pages: 4

LINK 14201-20 - DATASHEET FOR TOSHIBA PHONES

Brand: Jabra Pages: 2

Brand: ATZ Pages: 8

EXT-DVIKVM-441DL

Brand: Gefen Pages: 32

Brand: Little Giant Pages: 2

Brand: I-Tech Pages: 39

PMV WM Ultraswitch

Brand: Flowserve Pages: 16

LNK-IMC208P-SFP

Brand: E-LINK Pages: 6

Brand: Ruby Tech Pages: 2

Brand: steute Pages: 20

Brand: Jerguson Pages: 16

Brand: HDTV Supply Pages: 21

Brand: LevelOne Pages: 15

Brand: Omron Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands