Dell Lattitude D600 Service Manual Download Page 39

Page: 39 / 77

Display Assembly and Display Latch: Dell Latitude D600 Service Manual

3 pull-tab on bottom flex-cable

connector

9. Press in both sides of the top display cable connector, and pull the display cable

connector away from the top flex-cable connector.

Display Latch

NOTICE:

Disconnect the computer and any attached devices from electrical

outlets, and remove any installed batteries.

NOTICE:

To avoid electrostatic discharge, ground yourself by using a wrist

grounding strap or by touching an unpainted metal surface on the computer.

1. Remove the

keyboard

2. Remove the

display assembly

3. Remove the

display bezel

4. Remove the two M2.5 x 4-mm screws that secure the display latch bracket to the

top cover.

5. Lift the display bracket out of the top cover, and then remove the display latch.

file:///F|/Service%20Manuals/Dell/Latitude/d600/display.htm (9 of 10) [2/28/2004 8:15:47 AM]

Summary of Contents for Lattitude D600














































































Search results

Summary of Contents for Lattitude D600

Reviews:

Related manuals for Lattitude D600

Brands by name

Popular brands

Dell Lattitude D600, Service Manual

Search results

Summary of Contents for Lattitude D600

Reviews:

Related manuals for Lattitude D600

Brands by name

Popular brands