Dell Lattitude D600 Service Manual Download

Page: 25 / 77

Hard Drive: Dell Latitude D600 Service Manual

5. Remove the new drive from its packaging.

Save the original packaging to use when storing or shipping the hard drive.

NOTICE:

If you do not open the display before you replace your hard drive, you

might permanently scratch your display bezel.

6. Open the display approximately 1/2 inch.

NOTICE:

Use firm and even pressure to slide the drive into place. If you force

the hard drive into place using excessive force, you may damage the connector.

7. Press the hard drive cover down until it is fully seated in the bay, and tighten

the screw.

8. Use the

Operating System

CD to install the operating system for your computer.

9. Use the

Drivers and Utilities

CD to install the drivers and utilities for your

computer.

file:///F|/Service%20Manuals/Dell/Latitude/d600/hdd.htm (3 of 4) [2/28/2004 8:15:45 AM]

Summary of Contents for Lattitude D600














































































Search results

Summary of Contents for Lattitude D600

Reviews:

Related manuals for Lattitude D600

Brands by name

Popular brands

Dell Lattitude D600, Service Manual

Search results

Summary of Contents for Lattitude D600

Reviews:

Related manuals for Lattitude D600

Brands by name

Popular brands