Dell Latitiude E6500 Service Manual Download Page 29

Page: 29 / 72

Back to Contents Page

Fan

Dell™ Latitude™ E6500 Service Manual

Removing the Fan

Replacing the Fan

Removing the Fan

Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the
Regulatory Compliance Homepage at: www.dell.com/regulatory_compliance.

Follow the instructions in

Before Working on Your Computer

Close the display and turn the computer over.

Remove the bottom of the base assembly (see

Removing the Bottom of the Base Assembly

Remove the three M2.5 x 5-mm screws that secure the fan to the base of the computer.

Disconnect the fan connector from the system board.

Lift the fan up at an angle to remove it.

Replacing the Fan

Insert the fan at an angle, and push down aligning the screws holes in the fan with the screw holes in the heat sink.

Replace the three M2.5 x 5-mm screws to secure the fan to the base of the computer.

Connect the fan connector to the system board connector.

Replace the bottom of the base assembly (see

Replacing the Bottom of the Base Assembly

Back to Contents Page

1 fan

2 M2.5 x 5-mm screws (3)

3 fan connector

Summary of Contents for Latitiude E6500









































































Search results

Summary of Contents for Latitiude E6500

Reviews:

Related manuals for Latitiude E6500

Brands by name

Popular brands

Dell Latitiude E6500, Service Manual

Search results

Summary of Contents for Latitiude E6500

Reviews:

Related manuals for Latitiude E6500

Brands by name

Popular brands