Dell Latitiude E6500 Service Manual Download Page 22 | Manualshive

Page: 22 / 72

background image

1.

Disconnect the inverter backlight cable from the inverter.

2.

Lift the display panel out of the display cover and lay the display panel flat on your workspace.

3.

Disconnect the display cable and press the release tabs to remove the cable.

4.

Remove the display panel brackets, if needed (see

Removing the Display Panel Brackets

).

Removing the LED Display Panel

1.

Lift the display panel out of the display cover and lay the display panel flat on your workspace.

2.

Pull the pull-tab to disconnect the display cable.

Replacing the Display Panel

Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the
Regulatory Compliance Homepage at: www.dell.com/regulatory_compliance.

1 M2.5 x 5-mm screws (4) 2 display panel

3 display cover

4 inverter backlight cable

CAUTION:

Be careful not to damage the display with the hinges and cables on the display cover.

1 M2.5 x 5-mm screws (4) 2 display panel

3 display cover

CAUTION:

Be careful not to damage the display with the hinges and cables on the display cover.

«
...
20
21
22
23
24
...
»

Summary of Contents for Latitiude E6500









































































Reviews:

No comments

Related manuals for Latitiude E6500

THINKPAD I 1200 -

Brand: IBM Pages: 233

ASPIRE ONE 1410

Brand: Acer Pages: 256

ASPIRE ONE 1410

Brand: Acer Pages: 105

Brand: bto Pages: 216

Brand: Fujitsu Pages: 89

Brand: Fujitsu Pages: 80

Brand: Fujitsu Pages: 108

Brand: Fujitsu Pages: 126

Brand: Fujitsu Pages: 320

Brand: Fujitsu Pages: 67

LIFEBOOK TH4410

Brand: Fujitsu Pages: 124

Brand: Fujitsu Pages: 121

Brand: Fujitsu Pages: 413

Brand: Fujitsu Pages: 64

Brand: Sony Pages: 1

Brand: Sony Pages: 1

Brand: Sony Pages: 1

Brand: Sony Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands