manualshive.com logo in svg

Dell Latitiude E6500, Service Manual

Share
Download
Dell Latitiude E6500 Service Manual Download Page 37

Back to Contents Page

  

 

 LED Cover  

Dell™ Latitude™ E6500 Service Manual 

 

  

Removing the LED Cover 

 

  

Replacing the LED Cover 

 

 

 

Removing the LED Cover  

Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the 
Regulatory Compliance Homepage at: www.dell.com/regulatory_compliance. 

 

 

1.

Follow the procedures in 

Before Working on Your Computer

.  

 

 

  

2.

Using a plastic scribe, starting from the right edge of the LED cover, gently pry up the LED cover.  
 

 

  

3.

Remove the LED cover from the computer.  
 

  

 

Replacing the LED Cover  

Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the 
Regulatory Compliance Homepage at: www.dell.com/regulatory_compliance. 

 

 

1.

Replace the LED cover.  
 

 

  

2.

Starting from the outer edge, gently push down the LED cover until it locks into place.  
 

Back to Contents Page

 

 

 

1  LED cover  2  scribe 

Summary of Contents for Latitiude E6500









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands