Dell Inspiron X200 Service Manual Download Page 11

Page: 11 / 72

Battery: Dell Latitude X200 Service Manual

Back to Contents Page

Battery

Dell™ Latitude™ X200 Service Manual

Removing the Battery

NOTICE:

If you choose to replace the battery with the computer in standby

mode, you have up to 1 minute to complete the battery replacement before the

computer shuts down and loses any unsaved data.

1. Ensure that the computer is turned off, suspended in a power management

mode, or connected to an electrical outlet.

2. If the computer is docked, undock it.

3. Slide the battery lock latch on the bottom of the computer to the unlock

position.

4. Slide and hold the battery latch release on the bottom of the computer, and

then remove the battery from the bay.

file:///F|/Service%20Manuals/Dell/Latitude/x200/battery.htm (1 of 3) [2/28/2004 8:23:56 AM]

Summary of Contents for Inspiron X200









































































Search results

Summary of Contents for Inspiron X200

Reviews:

Related manuals for Inspiron X200

Brands by name

Popular brands

Dell Inspiron X200, Service Manual

Search results

Summary of Contents for Inspiron X200

Reviews:

Related manuals for Inspiron X200

Brands by name

Popular brands