manualshive.com logo in svg

Dell Inspiron X200, Service Manual

Share
Download
Dell Inspiron X200 Service Manual Download Page 55

System Board: Dell Latitude X200 Service Manual

15.  

Remove the modem daughter card

, and set it aside to install in the replacement 

system board. 

Replacing the System Board 

1.  

Install the modem daughter card

 that you removed from the old system board 

in the replacement system board. 

2.  Place the system board in the bottom case. 

NOTE: 

Route cables so that they will not be crimped or pinched when the 

complete assembly is put back together. 

3.  Reconnect the status light (LED) cable to the system board ZIF connector. 

4.  Reinstall the four M2 x 4-mm screws that secure the system board to the 

bottom case. 

NOTE: 

After replacing the system board, enter the computer service tag 

sequence into the BIOS of the replacement system board. 

Back to Contents Page

 

 

 

file:///F|/Service%20Manuals/Dell/Latitude/x200/sysboard.htm (3 of 3) [2/28/2004 8:24:04 AM]

Summary of Contents for Inspiron X200









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands