Dell Inspiron 5680 Page 78 Service Manual Download

Page: 78 / 130

Replacing the processor fan

WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in

Before

working inside your computer

. After working inside your computer, follow

the instructions in

After working inside your computer

. For more safety best

practices, see the Regulatory Compliance home page at

www.dell.com/

regulatory_compliance

Procedure

Align the screw holes on the processor fan with the screw holes on the heat
sink.

Replace the four screws (M3x7.26) that secure the processor fan to the heat
sink.

Align the processor fan and heat-sink assembly to the slot on the processor.

Align the slots on the release-lever with the securing tabs on both sides of the
processor.

Pivot the release-lever backwards and secure processor fan and heat-sink
assembly on the processor.

Connect the processor-fan cable to the system board.

Place the computer in an upright position.

Post-requisites

Replace the

right-side cover

Summary of Contents for Inspiron 5680



































































































































Search results

Summary of Contents for Inspiron 5680

Reviews:

Related manuals for Inspiron 5680

Brands by name

Popular brands

Dell Inspiron 5680, Service Manual

Search results

Summary of Contents for Inspiron 5680

Reviews:

Related manuals for Inspiron 5680

Brands by name

Popular brands