Dell Inspiron 15 5515 Service Manual Download Page 63

Page: 63 / 76

Next steps

1. Install the

display assembly

2. Install the

touchpad

3. Install the

speakers

4. Install the

power-adapter port

5. Install the

power-button with optional fingerprint reader

6. Install the

system board

NOTE:

The system board can be installed along with the heat sink.

7. Install the

I/O board

8. Install the

fan

9. Install the

coin-cell battery

10. Install the

wireless card

11. Install the

M.2 2280 solid-state drive

M.2 2230 solid-state drive

in M.2 slot one, whichever applicable.

12. Install the

M.2 2230 solid-state drive

in M.2 slot two, if applicable.

13. Install the

memory module

14. Install the

3-cell battery

4-cell battery

, whichever applicable.

15. Install the

base cover

16. Follow the procedure in

After working inside your computer

Removing and installing components

Summary of Contents for Inspiron 15 5515













































































Search results

Summary of Contents for Inspiron 15 5515

Reviews:

Related manuals for Inspiron 15 5515

Brands by name

Popular brands

Dell Inspiron 15 5515, Service Manual

Search results

Summary of Contents for Inspiron 15 5515

Reviews:

Related manuals for Inspiron 15 5515

Brands by name

Popular brands