Dell Inspiron 15 5515 Service Manual Download Page 18 | Manualshive

Page: 18 / 76

background image

Installing the 3-cell battery

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following image indicates the location of the 3-cell (41 Wh) battery and provides a visual representation of the installation
procedure.

Steps

1. Using the alignment posts, place the 3-cell battery on the palm-rest and keyboard assembly.
2. Align the screw holes on the 3-cell battery with the screw holes on the palm-rest and keyboard assembly.
3. Replace the three (M2x3) screws that secure the 3-cell battery to the palm-rest and keyboard assembly.
4. Connect the battery cable to the system board.
5. Adhere the tape that secures the battery cable to the system board.

Next steps

1. Install the

.

2. Follow the procedure in

After working on your computer

.

Removing the 4-cell battery

Prerequisites

1. Follow the procedure in

Before working inside your computer

.

2. Remove the

.

About this task

The following image indicates the location of the 4-cell (54 Wh) battery and provides a visual representation of the removal
procedure.

18

Removing and installing components

«
...
16
17
18
19
20
...
»

Summary of Contents for Inspiron 15 5515













































































Reviews:

No comments

Related manuals for Inspiron 15 5515

Brand: OLPC Pages: 37

Brand: Olivetti Pages: 52

Brand: MSI Pages: 102

ATLAS 14.1" N370

Brand: Kogan Pages: 16

Brand: Acer Pages: 79

Brand: Acer Pages: 83

Brand: Acer Pages: 72

Brand: Acer Pages: 83

Brand: Acer Pages: 78

eMachines eM250

Brand: Acer Pages: 194

eMachines E630 Series

Brand: Acer Pages: 198

ENDURO Urban N3 Lite

Brand: Acer Pages: 80

Brand: Asus Pages: 102

Brand: MSI Pages: 90

Brand: MSI Pages: 80

Brand: MSI Pages: 74

Brand: MSI Pages: 102

Brand: AIRIS Pages: 104

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands