Dell Inspiron 15 5515 Service Manual Download Page 38

Page: 38 / 76

Steps

1. Adhere the coin-cell battery to the slot on the palm-rest and keyboard assembly.
2. Connect the coin-cell battery cable to the I/O board.

Next steps

1. Install the

base cover

2. Follow the procedure in

After working inside your computer

Heat sink

Removing the heatsink

Prerequisites

1. Follow the procedure in

Before working inside your computer

CAUTION:

For maximum cooling of the processor, do not touch the heat transfer areas on the heat sink. The

oils in your skin can reduce the heat transfer capability of the thermal grease.

NOTE:

The heat sink may become hot during normal operation. Allow sufficient time for the heat sink to cool before you

touch it.

2. Remove the

base cover

About this task

The following images indicate the location of the heatsink and provide a visual representation of the removal procedure.

Removing and installing components

Summary of Contents for Inspiron 15 5515













































































Search results

Summary of Contents for Inspiron 15 5515

Reviews:

Related manuals for Inspiron 15 5515

Brands by name

Popular brands

Dell Inspiron 15 5515, Service Manual

Search results

Summary of Contents for Inspiron 15 5515

Reviews:

Related manuals for Inspiron 15 5515

Brands by name

Popular brands