Dell Inspiron 15 5515 Service Manual Download Page 53 | Manualshive

Page: 53 / 76

background image

4. Remove the

memory module

.

5. Remove the

M.2 2280 solid-state drive

or

M.2 2230 solid-state drive

from M.2 slot one, whichever applicable.

6. Remove the

M.2 2230 solid-state drive

from M.2 slot two, if applicable.

7. Remove the

wireless card

.

8. Remove the

.

9. Remove the

.

About this task

NOTE:

When removing the system board to replace/access other parts, the system board can be removed and installed

with the heat sink attached in order to simplify the procedure and preserve the thermal bond between the system board
and heat-sink.

The following image indicates the connectors on your system board.

Figure 1. System board connectors

1. Display cable connector
2. Power-adapter port cable connector
3. Keyboard backlit cable connector
4. Keyboard cable connector
5. Touchpad cable connector
6. Battery cable connector
7. Fan cable connector
8. Speaker cable connector
9. I/O-board cable connector

The following images indicate the location of the system board and provide a visual representation of the removal procedure.

Removing and installing components

53

«
...
51
52
53
54
55
...
»

Summary of Contents for Inspiron 15 5515













































































Reviews:

No comments

Related manuals for Inspiron 15 5515

Toughbook CF-Y5LWEZABM

Brand: Panasonic Pages: 40

Brand: Compaq Pages: 134

Brand: EUROCOM Pages: 90

Predator PTX17-71

Brand: Acer Pages: 44

Brand: Acer Pages: 13

Brand: Dell Pages: 23

Brand: Dell Pages: 22

Brand: Toshiba Pages: 4

Brand: Toshiba Pages: 4

Brand: Toshiba Pages: 4

Brand: Toshiba Pages: 4

Brand: Toshiba Pages: 4

Brand: Toshiba Pages: 4

Brand: Toshiba Pages: 4

Brand: Toshiba Pages: 4

Brand: Toshiba Pages: 4

Brand: Toshiba Pages: 4

Brand: Toshiba Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands