manualshive.com logo in svg

Dell Inspiron 11-3147 2-in-1, Owner'S Manual

Share
Download
Dell Inspiron 11-3147 2-in-1 Owner'S Manual Download Page 70

Removing the Windows-

Button Board

WARNING: Before working inside your computer, read the safety 
information that shipped with your computer and follow the steps in 

Before Working Inside Your Computer

. After working inside your 

computer, follow the instructions in 

After Working Inside Your 

Computer

. For more safety best practices, see the Regulatory 

Compliance home page at dell.com/regulatory_compliance. 

Prerequisites

1 

Remove the 

base cover

.

2 

Remove the 

battery

.

3 

Remove the 

display assembly

.

4 

Remove the 

display back-cover and antenna assembly

.

Procedure

CAUTION: Place the display-panel assembly on a soft and clean 

surface to avoid scratching the display.

1 

Place the display-panel assembly face down on a flat surface.

2 

Peel off the adhesive tape to access the Windows-button board cable.

3 

Lift the connector latches and disconnect the Windows-button board 

cable and the touch-board cable from the Windows-button board.

4 

Remove the screw that secures the Windows-button board to the display 

bezel.

70

Summary of Contents for Inspiron 11-3147 2-in-1
















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands