Dell EMC VxFlex Ready Node 14G Manual Download Page 4

Page: 4 / 76

Determine the 2U1N node type...................................................................42
R640 and R740xd server NIC and BMC (iDRAC) port locations................. 42
VxFlex Ready Node R640 and R740xd port designations - ESXi.................44

Configure the Management IP address - ESXi............................... 47

Installing the drivers

Install the VxFlex OS drivers.......................................................................50

Preparing Disks

Adding disks to a VxFlex OS SDS............................................................... 54
Verify the disk controller type.................................................................... 54
Enable PERCCLI on an ESXi server............................................................ 55
Create virtual devices with PERCCLI......................................................... 56

Verify the storage and disk controller status ................................ 56
Create virtual devices for HDD with PERCCLI...............................58
Create virtual devices for SSD with PERCCLI............................... 59
Ensure virtual disk creation with PERCCLI.................................... 59

Additional Configurations

Install OpenManage Essentials................................................................... 64
Activate the NVIDIA GPU on the server..................................................... 64
Installing the iDRAC Service Module on an ESXi server..............................64

Install the iSM using SSH.............................................................. 65
Install the iSM using the vSphere CLI............................................ 65

Where to go from here............................................................................... 66

Reference material

DTK - Hardware Update Bootable ISO........................................................68

Dell OpenManage DRAC Tools (RACADM)....................................68
Recommended BIOS and firmware settings...................................70
Troubleshooting the Hardware ISO................................................73
Additional resources...................................................................... 75

Chapter 6

Chapter 7

Chapter 8

Chapter 9

CONTENTS

Hardware Configuration and Operating System Installation Guide - ESXi Servers

Summary of Contents for EMC VxFlex Ready Node 14G













































































Search results

Summary of Contents for EMC VxFlex Ready Node 14G

Reviews:

Related manuals for EMC VxFlex Ready Node 14G

Brands by name

Popular brands

Dell EMC VxFlex Ready Node 14G, Manual

Search results

Summary of Contents for EMC VxFlex Ready Node 14G

Reviews:

Related manuals for EMC VxFlex Ready Node 14G

Brands by name

Popular brands