manualshive.com logo in svg

Dell EMC VxFlex Ready Node 14G, Manual, Page: 57 / 76

Share
Download
Dell EMC VxFlex Ready Node 14G Manual Download Page 57

l

Removing all the existing VDs from the node

l

Setting up the controller card boot parameter

Procedure

1. Log in to the node.

2. Display the disk information on the node:

/opt/lsi/perccli/perccli /c0/eall/sall show

Output similar to the following is displayed:

The output shows the following:

l

Enclosure ID (EID): Used in a later step when creating VDs

l

Slot ID (SLT) of each drive: Used in a later step when creating VDs

l

Drive type: Displays SSD or HDD as the device type. (SSD drives are smaller
—744 GB in this case.)

l

Drive state: Should be UGood (unused and good)

3. Verify that the VDs exist on the node:

/opt/lsi/perccli/perccli /c0/vall show

Output similar to the following is displayed:

If the output confirms that VDs exist on the node, perform the next step to
remove them. Otherwise, skip the step.

4. Remove all existing VDs from the node:

/opt/lsi/perccli/perccli /c0/vall del

The VDs are removed.

Preparing Disks

Verify the storage and disk controller status 

     

57

Summary of Contents for EMC VxFlex Ready Node 14G













































































Reviews:

No comments