Dell EMC VxFlex Ready Node 14G Manual Download Page 66

Page: 66 / 76

Note

If you are using the vSphere CLI on a Linux server, perform the command from
any directory.

7. Install the iSM software:

esxcli --server

<host_IP>

software vib install - d /var/log/

vmware/

<iDRAC Service Module file>

8. At the prompt, type the root username and password of the ESXi host.

The command output tells you whether the installation succeeded.

9. Right-click the ESXi host and select Power

Reboot.

10. Optionally view the information about the installed VIBs:

esxcli --server

<IP>

software vib get

software vib list

11. From the iDRAC web interface, open the iDRAC settings

Overview page and

ensure that the iDRAC Service Module status is Running

Where to go from here

Continue by deploying the VxFlex OS system.

For instructions, see the

VxFlex Ready Node VMware Quick Start Guide

Additional Configurations

Hardware Configuration and Operating System Installation Guide - ESXi Servers

Summary of Contents for EMC VxFlex Ready Node 14G













































































Search results

Summary of Contents for EMC VxFlex Ready Node 14G

Reviews:

Related manuals for EMC VxFlex Ready Node 14G

Brands by name

Popular brands

Dell EMC VxFlex Ready Node 14G, Manual

Search results

Summary of Contents for EMC VxFlex Ready Node 14G

Reviews:

Related manuals for EMC VxFlex Ready Node 14G

Brands by name

Popular brands