manualshive.com logo in svg

Dell EMC PowerEdge T440, Manual

Share
Download
Dell EMC PowerEdge T440 Manual Download Page 80

Figure 32. Installing a 3.5 inch drive adapter into the 3.5 inch drive carrier

Next steps

1

Install the 3.5 inch drive carrier into the system.

2

If removed, install the front bezel.

Related links

Installing a 2.5 inch drive into a 3.5 inch drive adapter
Installing the front bezel

Optical drives and tape drives

Your system supports one of the following configurations:

•

Systems with cabled drives support one optical drive and one tape drive.

•

Systems with hot-swappable drives support up to one optical drive and two tape drives.

Removing the optical or tape drive blank

Prerequisites

1

Follow the safety guidelines listed in 

Safety instructions

.

2

Follow the procedure listed in 

Before working inside your system

.

3

If applicable, remove the front bezel.

Steps

1 

To remove the drive blank, slide the release latch down to release the drive blank.

2 

Push the drive blank to slide it out of the drive bay.

NOTE: 

Blanks must be installed on empty optical drive or tape drive slots to maintain FCC certification of the system. The 

brackets also keep dust and dirt out of the system and aid in proper cooling and airflow inside the system. Perform the same 
steps to install blanks.

80

Installation and Service Manual
Installing and removing system components

Summary of Contents for EMC PowerEdge T440























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands