manualshive.com logo in svg

Dell EMC PowerEdge T440, Manual

Share
Download
Dell EMC PowerEdge T440 Manual Download Page 121

5 

Place the heat sink on the processor and push down on the base of the heat sink until the bracket locks onto the heat sink.

NOTE: 

•

Ensure that the two guide pin holes on the bracket match the guide holes on the heat sink.

•

Do not press on the heat sink fins.

•

Ensure that the pin 1 indicator on the heat sink is aligned with the pin 1 indicator on the bracket before placing the heat sink 

onto the processor and bracket.

Figure 69. Installing the heat sink onto the processor

Next steps

1

Install the processor and heat sink module.

2

Install the air shroud.

3

Follow the procedure listed in 

After working inside your system

.

Related links

Installing a processor and heat sink module
Installing the air shroud

Installation and Service Manual

Installing and removing system components

121

Summary of Contents for EMC PowerEdge T440























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands