manualshive.com logo in svg

Dell EMC PowerEdge T440, Manual

Share
Download
Dell EMC PowerEdge T440 Manual Download Page 131

Figure 79. Removing the system battery

3 

To install a new system battery, hold the battery with the positive side facing up and slide it under the securing tabs.

4 

Press the battery into the connector until it snaps into place.

Figure 80. Installing the system battery

Next steps

1

If applicable, connect the cables to the expansion card(s).

2

Follow the procedure listed in 

After working inside your system

.

3

While booting, press F2 to enter the System Setup and ensure that the battery is operating properly.

4

Enter the correct time and date in the System Setup 

Time

 and 

Date

 fields.

5

Exit the System Setup.

Related links

System board jumpers and connectors

Control panel assembly

Removing the control panel assembly

Prerequisites

1

Follow the safety guidelines listed in 

Safety instructions

.

2

Follow the procedure listed in 

Before working inside your system

.

Steps

1 

Using the Phillips #2 screwdriver, remove the screw that secures control panel to the chassis.

2 

Disconnect the control panel cable and the control panel USB cable from the system board.

CAUTION: 

Do not use excessive force when removing the control panel cables as it can damage the connectors.

3 

Slide the control panel out of the chassis.

NOTE: 

Follow the same steps to remove the control panel in the rack-mode configuration.

Installation and Service Manual

Installing and removing system components

131

Summary of Contents for EMC PowerEdge T440























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands