Dell Alienware Area-51m R2 Service Manual Download Page 43 | Manualshive

Page: 43 / 94

background image

2. Remove the

3. Remove the

4. Remove the

5. Remove the

solid-state drive from M.2 slot two

6. Remove the

7. Remove the

About this task
The following image indicates the location of the card-reader board and provides a visual representation of the removal procedure.

Steps
1. Using the pull tab, disconnect the card-reader board cable from the system board.
2. Remove the three screws (M2.5x2.5) that secure the card-reader board to the palm-rest assembly.
3. Remove the card-reader board cable from the routing guides on the palm-rest assembly.
4. Lift the SD card reader board off the palm-rest assembly.

Installing the card-reader board

Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.

About this task
The following image indicates the location of the card-reader board and provides a visual representation of the installation

procedure.

43

«
...
41
42
43
44
45
...
»

Summary of Contents for Alienware Area-51m R2































































































Reviews:

No comments

Related manuals for Alienware Area-51m R2

Brand: Gateway Pages: 158

Brand: M5Stack Pages: 15

Brand: Markant Pages: 11

Brand: 7starlake Pages: 48

Brand: Gigabyte Pages: 2

Brand: BE QUIET! Pages: 48

Brand: Arista Pages: 47

Brand: Jupiter Pages: 2

Brand: Jesco Pages: 56

Brand: Avid Technology Pages: 19

Brand: Asus Pages: 87

Brand: Ergo Pages: 33

Brand: Fanvil Pages: 52

Brand: Fanvil Pages: 54

Brand: Nimbus Water Systems Pages: 66

Stockholm Micro Desk

Brand: FRISKA Pages: 20

Brand: ALTUS Pages: 14

Brand: DTK Computer Pages: 118

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands