Dell Alienware Area-51m R2 Service Manual Download

Page: 15 / 94

• If the battery gets stuck inside your computer as a result of swelling, do not try to release it as puncturing, bending, or

crushing a lithium-ion battery can be dangerous. In such an instance, contact Dell technical support for assistance. See

www.dell.com/contactdell

• Always purchase genuine batteries from

www.dell.com

or authorized Dell partners and resellers.

Removing the battery

Prerequisites
1. Follow the procedure in

Before working inside your computer

2. Remove the

base cover

About this task
The following image indicates the location of the battery and provides a visual representation of the removal procedure.

Steps
1. Using the pull tab, disconnect the battery cable from the system board and remove it from the routing guides on the computer

base, if applicable.

2. Remove the six screws (M2.5x5) that secure the battery to the palm-rest assembly.
3. Lift the battery off the palm-rest assembly.

Installing the battery

Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.

About this task
The following image indicates the location of the battery and provides a visual representation of the installation procedure.

Summary of Contents for Alienware Area-51m R2































































































Search results

Summary of Contents for Alienware Area-51m R2

Reviews:

Related manuals for Alienware Area-51m R2

Brands by name

Popular brands

Dell Alienware Area-51m R2, Service Manual

Search results

Summary of Contents for Alienware Area-51m R2

Reviews:

Related manuals for Alienware Area-51m R2

Brands by name

Popular brands