Dell Alienware Area-51 R5 Service Manual Download Page 19

Page: 19 / 121

Removing the stability foot

NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow the
steps in

Before working inside your computer

. After working inside your computer, follow the instructions in

After working

inside your computer

. For more safety best practices, see the Regulatory Compliance home page at

www.dell.com/

regulatory_compliance

Procedure

1. Tilt the computer towards the front until the base is facing up.

2. Remove the two screws (#6-32x6) that secure the stability foot to the computer.
3. Lift the stability foot off the computer.

4. Tilt the computer back to the upright position.

Summary of Contents for Alienware Area-51 R5


























































































































Search results

Summary of Contents for Alienware Area-51 R5

Reviews:

Related manuals for Alienware Area-51 R5

Brands by name

Popular brands

Dell Alienware Area-51 R5, Service Manual

Search results

Summary of Contents for Alienware Area-51 R5

Reviews:

Related manuals for Alienware Area-51 R5

Brands by name

Popular brands