Dell 1600n - Multifunction Laser Printer B/W Service Manual Download Page 103

Page: 103 / 189

Troubleshooting

Service Manual

7-13

7.3.7 Uneven Density

• Description

Print density is uneven between left and right.

Check and Cause

Solution

1. The pressure force on the left and right

springs of the transfer roller is not even,
the springs are damaged, the transfer
roller is improperly installed, or the trans-
fer roller bushing or holder is damaged.

2. The life of the Developer has expired.

3. The toner level is not even on the devel-

oper roller due to the bad blade.

1. Replace both the left and right Spring

Holder.

2. Problem with the toner cartridge, replace

the toner cartridge and try to print out.

7.3.8 Background

• Description

Light dark background appears in whole area of the printing.

Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer

Check and Cause

Solution

1. Recycled recording paper has been

used.

2. The life of the Developer has expired.

3. The up-to-down movement of the trans-

fer roller is swift?

4. The HVPS is normal?

(Perform Engine Test Mode diagnostic
code 4)

1. Quality is not guaranteed when using recy-

cled paper.

2. Replace the toner cartridge.

3. Clean the busing on the transfer roller.

4. Replace the HVPS.

Summary of Contents for 1600n - Multifunction Laser Printer B/W






























































































































































































Search results

Summary of Contents for 1600n - Multifunction Laser Printer B/W

Reviews:

Related manuals for 1600n - Multifunction Laser Printer B/W

Brands by name

Popular brands

Dell 1600n - Multifunction Laser Printer B/W, Service Manual

Search results

Summary of Contents for 1600n - Multifunction Laser Printer B/W

Reviews:

Related manuals for 1600n - Multifunction Laser Printer B/W

Brands by name

Popular brands