Dell 1545 - Inspiron - Pentium 2 GHz Service Manual Download Page 38

Page: 38 / 51

Back to Contents Page

Wireless Mini-Card

Dell™ Inspiron™ 1545 Service Manual

Removing the Mini-Card

Replacing the Mini-Card

If you ordered a wireless Mini-Card with your computer, the card is already installed.

Your computer supports one half Mini-Card slot for WLAN.

Removing the Mini-Card

Follow the instructions in

Before You Begin

Remove the following parts based on the display adapter supported by your computer.

Mobile Intel

GMA:

Remove the base cover (see

Removing the Base Cover

ATI Mobility Radeon:

Remove the system board and turn it over (see

Removing the System Board

Disconnect the Mini-Card cables from the Mini-Card, if applicable.

Remove the screw that secures the Mini-Card to the system board connector.

Lift the Mini-Card out of the system board connector.

CAUTION:

Before working inside your computer, read the safety information that shipped with your computer. For additional safety best

practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.

NOTICE:

To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such

as a connector on the back of the computer).

NOTICE:

To help prevent damage to the system board, remove the main battery (see

Before Working Inside Your Computer

) before working inside the

computer.

NOTICE:

Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell™ is not

covered by your warranty.

NOTE:

Dell does not guarantee compatibility or provide support for Mini-Cards from sources other than Dell.

NOTE:

The WLAN slot supports a half Mini-Card.

NOTE:

Depending on the configuration of the system when it was sold, the Mini-Card slot may not have any Mini-Card installed.

NOTE:

The location of the Mini-Card may change according to the display adapter supported by your computer. To find the type of display adapter on

your computer, click

Start

Control Panel

System

Device Manager

Display adapters

1 Mini-Card 2 screw 3 antenna cable connectors (2)

Summary of Contents for 1545 - Inspiron - Pentium 2 GHz




















































Search results

Summary of Contents for 1545 - Inspiron - Pentium 2 GHz

Reviews:

Related manuals for 1545 - Inspiron - Pentium 2 GHz

Brands by name

Popular brands

Dell 1545 - Inspiron - Pentium 2 GHz, Service Manual

Search results

Summary of Contents for 1545 - Inspiron - Pentium 2 GHz

Reviews:

Related manuals for 1545 - Inspiron - Pentium 2 GHz

Brands by name

Popular brands