manualshive.com logo in svg

Dell 1545 - Inspiron - Pentium 2 GHz, Service Manual, Page: 28 / 51

Share
Download
Dell 1545 - Inspiron - Pentium 2 GHz Service Manual Download Page 28

Removing the Display Panel Cable 

 

 

1.

Remove the display assembly (see 

Removing the Display Assembly

).  

 

 

  

2.

Remove the display bezel (see 

Display Bezel

).  

 

 

  

3.

Remove the display panel (see 

Display Panel

).  

 

 

  

4.

Turn the display panel over and place it on a clean surface.  
 

  

 

 

5.

Lift the tape that secures the display panel cable to the connector on top and disconnect the cable from the connector.  
 

 

 

Replacing the Display Panel Cable 

 

 

1.

Reconnect the display cable to the connector on top.  
 

 

  

2.

Replace the display panel (see 

Replacing the Display Panel

).  

 

 

  

3.

Replace the display bezel (see 

Replacing the Display Bezel

).  

 

 

  

4.

Replace the display assembly (see 

Replacing the Display Assembly

).  

 

 

Display Inverter  

 

 

Removing the Display Inverter 

 

 

1.

Remove the display assembly (see 

Removing the Display Assembly

).  

 

 

  

2.

Remove the display bezel (see 

Removing the Display Bezel

).  

 

 

  

3.

Remove the display panel (see 

Removing the Display Panel

).  

 

 

  

4.

Disconnect the cables from the connectors on either side of the inverter board.  
 

 

NOTE: 

The display panel cables and connectors may differ depending on the display panel you ordered.

1  tape securing the display panel cable to the 

connector on top 

2  display panel 

cable 

3  back of display panel 

 

 

 

 

Summary of Contents for 1545 - Inspiron - Pentium 2 GHz




















































Reviews:

No comments