background image

Off

Power adapter is connected and the battery is fully charged.

Computer is running on battery and the battery has more than 5 percent charge.

Computer is in sleep state, hibernation, or turned off

NOTE: 

Hard-drive activity light is supported only on computers shipped with hard drive.

The power and battery-status light blinks amber along with beep codes indicating failures.

For example, the power and battery-status light blinks amber two times followed by a pause, and then blinks white three times followed by 
a pause. This 2,3 pattern continues until the computer is turned off indicating no memory or RAM is detected.

The following table shows different light patterns and describes what they indicate.

Table 14. Diagnostics

Light pattern

Problem description

2,1

CPU failure

2,2

System board: BIOS and ROM failure

2,3

No memory or RAM detected

2,4

Memory or RAM failure

2,5

Invalid memory installed

2,6

System board or chipset error

2,7

LCD failure

3,1

CMOS battery failure

3,2

PCI or video card or chip failure

3,3

Recovery image not found

3,4

Recovery image found but invalid

3,5

Power rail failure

3,6

SBIOS flash corruption

3,7

Timeout waiting on ME to reply to HECI message

Camera status light:

 Indicates whether the camera is in use.

Solid white — Camera is in use.

Off — Camera is not in use.

Caps Lock status light:

 Indicates whether Caps Lock is enabled or disabled.

Solid white — Caps Lock enabled.

Off — Caps Lock disabled.

Recovering the operating system

When your computer is unable to boot to the operating system even after repeated attempts, it automatically starts Dell SupportAssist OS 
Recovery.

Dell SupportAssist OS Recovery is a standalone tool that is preinstalled in all Dell computers installed with Windows 10 operating system. It 
consists of tools to diagnose and troubleshoot issues that may occur before your computer boots to the operating system. It enables you 
to diagnose hardware issues, repair your computer, back up your files, or restore your computer to its factory state.

You can also download it from the Dell Support website to troubleshoot and fix your computer when it fails to boot into their primary 
operating system due to software or hardware failures.

For more information about the Dell SupportAssist OS Recovery, see 

Dell SupportAssist OS Recovery User's Guide

 at 

www.dell.com/

support

.

84

Troubleshooting

Summary of Contents for Inspiron 3493
























































































Reviews: