manualshive.com logo in svg

Dell EMC Data Domain DS60, Hardware Manual

Share
Download
Dell EMC Data Domain DS60 Hardware Manual Download Page 89

7. Restart the Data Domain system. As the system boots up, the HOST/

EXPANSION LEDs on the shelf controller ports that are connected to the SAS
I/O module in the Data Domain system change from off to blue or green.

If any of these LEDs stays off or is not running at normal speed, it means there
is a problem in the connection between the system and the shelf. See the
section 

DS60 expansion shelf

 on page 11 for more information. Reseat or

replace the cable and check the LEDs again. If the connection still has a
problem, replace the controller module or the SAS I/O module.

Verifying shelf installation

The Data Domain system recognizes all data storage (system and attached shelves) as
part of a single file system volume.

WARNING

l

Do not remove or disconnect a shelf that has been added earlier. If a shelf is
disconnected, the file system volume is immediately disabled and all data in
the volume is lost.

l

To re-enable a shelf, reconnect the shelf or transfer the disks from the shelf
to another empty shelf chassis and connect.

l

If the data on a shelf is not available to the file system volume, the volume
cannot be recovered.

l

Unless the same disks are available to the file system, the DD OS must be re-
installed as directed by your contracted service provider or Online Support
site, 

http://support.emc.com

.

Procedure

1. After installing the new shelves, check the status of the SAS I/O module by

entering the 

disk port show summary

 command:

# 

disk port show summary

Port   Connection   Link      Connected       Status

       Type         Speed     Enclosure IDs

----   ----------   -------   -------------   -------

5a     SAS                                    offline

5b     SAS                                    offline

5c     SAS                                    offline

5d     SAS                                    offline

6a     SAS                                    offline

6b     SAS                                    offline

6c     SAS                                    offline

6d     SAS                                    offline

7a     SAS          24 Gbps   5               online

7b     SAS          24 Gbps   6               online

7c     SAS          24 Gbps   4               online

7d     SAS          24 Gbps   2, 3            online

8a     SAS          24 Gbps   5               online

8b     SAS          24 Gbps   6               online

8c     SAS          24 Gbps   4               online

8d     SAS          24 Gbps   2, 3            online

The output shows:

l

The 

offline

 status for each SAS connection, such as 

5a

, 

5b

, 

5c

, and so

on.

Post-Installation Tasks

Verifying shelf installation

     

89

Summary of Contents for Data Domain DS60





































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands