background image

29 

DESIGNED SECURITY INC       

800-272-3555            www.dsigo.com  

1402 Hawthorne Street   Bastrop, Texas 78602         Fax 512 321 9181   

Email: [email protected]

 

INS8300 

GUIDELINES FOR EVERYDAY USE 

(PROVIDE COPIES TO ALL TURNSTILE USERS) 

 

Optical Turnstiles are provided for greater security in your workplace.   

They help ensure that only authorized individuals will be allowed into the secure areas of your facility.   

You may find daily use of Optical Turnstiles becomes routine as you follow these basic guidelines: 

 

USER VALIDATION

  

“ID”  for access control can be of many types, from card readers to biometric systems.   

Please refer to instructions provided for reader operation by the manufacturer, or by your security director.  

 

 

Look  at  DISPLAY 

 status, then

  PRESENT  ID

 to 

the  Reader  mounted  on,  or  in,  the  right-hand 

bollard of the lane you are using.  It may beep to 

indicate your ID was read.  

 

 

Listen

  for  a 

BEEP

  after  the 

ID  has  been 

validated

 and/or 

watch

 the Display on the top of 

the right-hand bollard to indicate authorization.   

 

 

Next 

Look

 for a 

PROCEED 

 message to indicate 

that 

you are now authorized

 to pass through the 

lane.  

The barriers will automatically swing out

of the way

 allowing passage.   

 

CAUTION: 

AVOID TOUCHING THE BARRIER

, except in an Emergency, otherwise 

AN ALARM MAY SOUND

 

 

 

MOVE THROUGH THE LANE PROMPTLY.

  Avoid stopping or moving backward, as this will trigger the alarm. 

 

TIP: 

During passage through the lane, swinging items (purses, briefcases, etc) could be interpreted by the turnstile 

as a person tailgating you, or moving in the other direction, thus causing an alarm.   To avoid delays caused by 

false alarms, hold items high and close to your body, or at your side as you pass through the lane. 

 

 

IF ALARM SOUNDS

, exit the lane, 

STOP

 and wait for security personnel to respond. 

 

 

Once through the lane, continue moving ahead to clear the lane for other users. 

 

FREE EXIT MODE 

Some turnstiles may be configured for “Free-Exit,” meaning there is no requirement to present ID when leaving the secured 

area.  Look for 

PROCEED/BYPASS 

graphic on the right-hand side of the lanes when in Free-exit mode.   

 

 

As  you  enter  the  lane,

 

the  turnstile  will  sense  your  presence  and  direction 

 allowing  you  to  exit the 

secured area of the building.  

Barriers will automatically open for Free Exit. 

  Pass through turnstile as 

outlined above.   

 

 

Keep in mind that the sensors are active during Free-exit mode.  Keep any bags or packages high and close to 

your body, or at your side, and avoid swinging them, as this may cause an alarm, even in Free Exit mode. 

 

EMERGENCY USE 

 

 

During  an  emergency  you  may  push  through  the  Acrylic  Barriers.  Follow  established  procedure  for 

emergency egress of the building. 

DISPLAY GRAPHICS 

 

 

 

 

 

 

 

 

      LANE READY       PROCEED           ALARM             CLOSED 

                                   /BYPASS  

Summary of Contents for DSI ES8300








































Reviews:

Related manuals for DSI ES8300