background image

18 

DESIGNED SECURITY INC       

800-272-3555            www.dsigo.com  

1402 Hawthorne Street   Bastrop, Texas 78602         Fax 512 321 9181   

Email: [email protected]

 

INS8300 

BARRIER DRIVE ASSEMBLY 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The 

Motor/Barrier Assembly

 is the center section of the bollard, located between the two pedestals. 

 

Located above the Barrier is the 

Encoder

.  This is a very sensitive encoder used to detect 

Barrier position and provide this information to the PLC.  It is attached to the end of the shaft 

that drives the Barrier Panel. 

 

Below the Encoder is the 

Barrier Panel

.  Located on the same shaft. 

 

(Units with optional Locking will have Locking Solenoid hardware mounted on this shaft.) 

 

This  shaft  goes  into  a  shaft 

 Coupler

  that  allows  quick  removal  of  the  Motor/Gearbox  assembly  for 

maintenance and repair. 

 

Beneath the Coupler is the 

Motor/Gearbox Assembly

 that drives the Barrier. 

 

Above the Barrier will be located either the 

B  &  A  Sensors

 (near Encoder 1) or the 

B  &  A 

Retro-reflectors

  (near Encoder  2).    These  are  the  sensor  beams  that  detect  direction  of  travel, 

tailgating violations, and passage-complete for valid users.

 

ENCODER 

BARRIER PANEL 

COUPLER 

MOTOR/GEARBOX 

ASSEMBLY 

“B” & “A” SENSORS 

LOCKING 

SOLENOID 

(optional) 

Summary of Contents for DSI ES8300








































Reviews: