background image

Rev: 8/2008 

 

9 of 21 

36B, 36BX, 36H, 36HX, 52H, 52HX 

DEK

® 

is exclusively distributed by GXi International, LLC 

Heavy Duty Power Equipment 

Assembly Instructions 
 
 
Step 2(b):   Assembly Instructions for Mowers with Belt Drive System  (36B, 36BX) 

1)  Attach the handle bars using 2 bolts on each side of the fuel 

tank bracket.  Select the desired hole locations to adjust for 
the handle bar height.  For lower handle bars, use the top 
hole location as shown in the diagram.  For higher handle 
bars, use the lower hole location 

 
 
 
 
2)  Attach the clutch / brake control rods to the clutch brake as-

sembly on each side of the mower.  Adjust for desired level of 
sensitivity by turning the threaded lug on the rod.  The adjust-
ment may take a few attempts to achieve: equal balance be-
tween the two break handles so they feel the same; easy 
disengagement from the parking break detent built into the 
pistol grip handle; and full contact with the brake when the 
handle is retracted (see page 17 for more adjustment details).   

Hole location for higher handle bar positioning 

3)  Unfasten the blade activation rod from the control handle, 
insert it through the hole on the chassis of the mower, and 
attach the rod to the blade activation cam assembly as per the 
adjacent photo.  Ensure the cam is positioned in the “9 O’ 
clock” position when attaching the rod to accomplish the cor-
rect rod travel.  Once the rod is attached to the cam, re-attach 
the other rod end to the control handle again.  For correct rod 
adjustment, you want to maintain the “9 O’ clock” position of 
the cam with the blade activation control knob in the full “off” 
position.  Turn the threaded rod until it achieves the correct 
cam positioning. 

Threaded 
blade activa-
tion control 
rod. 

9 O’ Clock cam 
position when con-
necting the rod with 
the control handle 
in the “off” position 
achieves the cor-
rect adjustment 

4)  Attach the gear shift lever by inserting 
it through the slot in the fuel tank bracket 
and attaching it to the gear shifter bolt on 
the transmission.  Tighten the bolt se-
curely.  Feed the handle assembly 
through the slot from the engine side of 
the fuel tank bracket.  

Fuel tank bracket 
 
Gear shift lever 
 
Retaining nut attached to gear shift bolt 

Summary of Contents for 36B






















Reviews: