background image

Rev: 8/2008 

 

10 of 21 

36B, 36BX, 36H, 36HX, 52H, 52HX 

DEK

® 

is exclusively distributed by GXi International, LLC 

Heavy Duty Power Equipment 

For 52” Models 

 
There are a total of 4 connections to connect the pre-wired han-
dle bar assembly.  Route the wire harness as shown on the 
adjacent photo and make the following connections: 

1.  The smaller, white, 2-pin connector is routed through a hole 

in the chassis and is connected to the blade activation 
safety switch 2-pin connector. 

2.  The larger, white, 5-pin connector is connected to the mat-

ing connector at the rear of the Honda engine.   

3.  The black wire is connected to a ground lug located on the 

back of the Honda engine. 

4.  The yellow wire is attached to the bottom of the starter mo-

tor solenoid on the Honda engine. 

 
In addition, the battery terminal wires must be connected to 
provide power to the electric starter.  Attach the red and black 
battery terminal wires to the battery. 
 
Once all connections are made, the wire harness can be 
strapped into place permanently to the handle bars and chassis 
using the black wire-ties provided. 
 
 

For 36” Models 

 
The 36” models have the following connections: 
 

1.  The 36” hydro drive model has the same as “connection 

1” for the 52” models discussed above, connecting the 
blade activation safety switch located underneath the front 
of the chassis.  The wire harness is routed through a hole 
in the chassis as per the above diagrams. 

2.  For the belt drive 36” models, connect the blade activation 

safety switch located on the back of the chassis.  It is a 
two pin connector coming from a black switch box under 
the fuel tank bracket.  See adjacent photo. 

3. 

There are 2 engine connections from the wire harness.  A 
black wire that is attached to a ground lug on the engine 
and a red wire connector that is attached to the red wire 
crimp connector located at the rear of the Honda engine.  
The crimp on connector is typically covered with a green 
plastic sleeve.  The red wire is the engine kill switch wire.

 

 

Once all connections are made, the wire harness can be 
strapped into place permanently to the handle bars and chassis 
using the black wire-ties provided. 

Assembly Instructions 
 
 
Step 3:  Wire Harness Assembly and Connections 

 

36” belt drive 
blade activation 
safety switch 
location top 
view. 

Black ground 
wire for Honda 
engine. 
 
Red wire with 
crimp connec-
tors and typi-
cally a green 
plastic cover. 

Summary of Contents for 36B






















Reviews: