background image

                                    PIPE(TUBE)  CUTTER  Of  Best  Technology

            16

      www.s-cutter.co.kr

3-2.

S-LT  Series_RS  :  Pipe  transfer  device

1)  S-LT  Series_RS,  a  pipe  feeder,  is  designed  to  fix  a  pipe  to  the  machine  and  then   

adjust  its  height(up  and  down)  to  bring  the  urethane  into  close  contact  with  the 
bottom  of  the  pipe  and  turn  the  handle  to  feed  the  pipe  forward  or  backward  to 
situate  it  to  a  desired  cutting  position.

2)  The  S-LT  Series_RS  can  be  adjusted  depending  on  the  outside  diameter  of  a  pipe; 
      However,  no  additional  manipulation  is  required  when  it  is  applied  repeatedly  to  pipes   
      of  the  same  diameter. 

                   

4. How  to  cut  the  pipe

4-1. How  to  use  the  stopper  for  cutting

1)  Rotate  the  stopper  bolt  left  or  right  until  the  stopper  is  aligned  with  the  cutting 

position  of  the  cutting  blade,  as  shown  in  the  figure(Memory  programmable).

Forward

Backward

Descent

Ascent

Fixing  nut

stopper

Beveling  blade

Cutting  blade

                  stopper

                  stopper  bolt

Summary of Contents for S LT Series






























Reviews: