8
;
Before using this equipment, record the product identification information from the ID label into the inspection and
maintenance log of this manual.
;
This Floor Mount Base can only be used with the 3M Modular Jib System M200 manufactured by 3M. Do not attempt to use
the Floor Mount Base without first consulting the user instructions 5908372 for the 3M Modular Jib System M200.
Table 1 –
Specifications
System Specifications:
Compatability:
The Floor Mount Bases covered in this instruction are compatible with 3M™ DBI-SALA®
Flexiguard™ Modular Jib System M200.
Standards:
Designed and tested to CEN/Ts 16415:2013 (Type A), EN795:2012 (Type A), OSHA 1926.502, and
OSHA 1910.140.
Capacity:
See 3M™ DBI-SALA® Flexiguard™ Modular Jib System M200 instruction 5908372.
Maximum Arresting
Force:
All connecting systems (SRDs, Energy Absorbing Lanyards, etc.) used with the Floor Mount Base
must limit the Maximum Arresting Force to 1,350 lbf (6 kN).
Weight:
8530888: 265 lb. (120 kg)
8530889: 377 lb. (171 kg)
Component Specifications:
Component
Material
General Construction
Welded Steel
Structural Material
A36 Steel
Base Finish
8530888 - Powdercoat
8530889 - Zinc Plating, Powdercoat
8530889 Base Cap
Aluminum, Stainless Steel Ring, Rubber Gasket
Mounting Requirements:
Model
Number
Minimum Fastener Pullout
Force
Mounting Structure Minimum
Moment Load
Mounting Structure Minimum
Vertical Load
8530888
9,386 lb. (4,257 kg)
501,633 in*lb. (680,124 N*m)
3,320 lb. (1,506 kg) + Base Weight
+ Jib Weight
8530889
501,633 in*lb. (680,124 N*m)
3,320 lb. (1,506 kg) + Base Weight
+ Jib Weight
;
See the fastener manufacturer’s specifications for fastener requirements.
1.0 PRODUCT APPLICATION
1.1
PURPOSE:
The Floor Mount Base is designed for use as a component of a Fall Protection System.
1.2
DESCRIPTION:
The Floor Mount Base (Figure 1)
is designed to be anchored to approved structures and used as a mounting
point for 3M approved Modular Jib System M200.
1.3
STANDARDS:
The Floor Mount Base conforms to the national or regional standard(s) identified on the front cover of these
instructions. If the product is resold outside of the original country of destination, the re-seller must provide these instructions in
the language of the country in which the product will be used.
1.4
SUPERVISION:
Installation of this equipment must be supervised by a Qualified Person¹. Use of this equipment must be
supervised by a Competent Person².
1.5
TRAINING:
This equipment must be installed and used by persons trained in its correct application. This manual is to be
used as part of an employee training program as required by national, regional, or local standards. It is the responsibility
of users and installers of this equipment to ensure they are familiar with these instructions, trained in the correct care
and use of this equipment, and are aware of the operating characteristics, application limitations, and consequences of
improper use of this equipment.
1.6 RESCUE PLAN:
When using this equipment and connecting subsystem(s), the employer must have a rescue plan and
the means at hand to implement and communicate that plan to users, authorized persons³, and rescuers
4
. A trained,
onsite rescue team is recommended. Team members should be provided with the equipment and techniques to perform a
successful rescue. Training should be provided on a periodic basis to ensure rescuer proficiency.
1.7
AFTER A FALL:
If this equipment is subjected to fall arrest or impact forces, remove it from service immediately. Clearly
tag it “DO NOT USE”. See section 4 for more information.
1 Qualified Person:
A person with a recognized degree, certificate or professional standing, or who by extensive knowledge, training and experience has success
-
fully demonstrated his ability to solve or resolve problems relating to Fall Protection systems to the extent required by OSHA or other applicable federal, state, and
local regulations.
2 Competent Person:
One who is capable of identifying existing and predictable hazards in the surroundings or working conditions which are unsanitary, haz
-
ardous, or dangerous to employees, and who has authorization to take prompt corrective measures to eliminate them.
3 Authorized Person:
A person assigned by the employer to perform duties at a location where the person will be exposed to a fall hazard.
4 Rescuer:
Person or persons other than the rescue subject acting to perform an assisted rescue by operation of a rescue system.
Summary of Contents for 3M Flexiguard M200
