background image

T

R O U B L E S H O O T I N G

  G

U I D E

Program Problems

15

?

WeatherLink says “No new data to download” but I know there’s data there. What can 
I do?

Vantage is smart enough to send only data it hasn’t already sent to the com-
puter. So, when you initiate a new download, the program will retrieve the 
first record after the last record shown in the WeatherLink’s Browse Window. 
Older data is stored in the logger as a backup. To see how many of these 
backup records are stored in the logger, create a new station and download 
the data into this new database. Because there are no records stored in the sta-
tion you just created, WeatherLink will download everything it has stored.

Next, try clearing the archive memory using the clear dialog box. You will lose 
any data not already downloaded in your archive memory, but all of your cal-
ibration numbers and alarm settings will remain intact. If this doesn’t work, 
reboot your weather station (that is, remove, then restore all power to the sta-
tion). 

Note:

Make sure to put the console in Setup Mode (by pressing the DONE and DOWN arrow 
keys) before removing the batteries. The ensures the station will not try to write any data 
when the power goes off.

?

After successfully downloading, recent or new data does not appear to be in my data-
base. Where is it?

Check to see if the time and date on your station are incorrect. (This can hap-
pen if you have a power outage and your battery backup is dead.) If so, the 
data was written into the wrong month, day, and/or time. Reset the time and 
date. 

It is also possible, if you have multiple stations, that you downloaded data 
into the wrong station’s database. Make sure you’ve opened the correct sta-
tion before downloading.

?

When viewing data, dashes appear in place of a value for functions other than wind 
direction. Why?

If no data was recorded by a sensor (for example, the sensor was disconnected 
or radio interference blocked reception) or if bad data was recorded for a sen-
sor (for example, the sensor was malfunctioning), the software dashes out the 
entry rather than showing invalid data. You can use the record editor to cor-
rect these entries.

Summary of Contents for and Vantage Pro

















Reviews: