background image

 

H

 

A R D W A R E

 

  I

 

N S T A L L A T I O N

 

Hardware Requirements

 

4

 

H

 

A R D W A R E

 

  I

 

N S T A L L A T I O N

 

WeatherLink allows two types of installation: direct connection and phone 
modem connection. Direct connection means connecting the computer directly to 
the station. Phone modem connection refers specifically to any installation where 
the station is connected to a modem and you communicate with the station and 
data logger via a modem at your computer. Requirements and installation for 
each type of connection differ, and are explained separately below.

 

H

 

A R D W A R E

 

  R

 

E Q U I R E M E N T S

 

The required hardware differs depending on whether you are making a direct 
connection or a phone modem connection.

 

Direct Connection Hardware Requirements

 

In addition to the provided hardware, the following are required for a direct con-
nection.

 

 

Computer running Windows™ 95, 98, 2000, ME or NT 4.0 with at least 5 MB of free 
disk space

 

The amount of space necessary for the data files depends on the archive inter-
val. Database files containing data stored at a 30 minute archive interval 
require approximately 36K of disk space per month of data. The file size 
changes in a linear fashion depending on the archive interval. For example, 
data stored at a 1–minute interval requires approximately 1 MB/month while 
the data stored at a 2–hour interval requires approximately 9K/month.

 

 

Windows-Compatible Display

 

VGA minimum. SVGA or High (16-bit) Color recommended.

 

 

One Free Serial Port

Phone Modem Connection Hardware Requirements

 

In addition to the provided hardware and the computer equipment listed above, 
the following hardware is required for a phone modem connection.

 

 

One external modem to connect to the data logger

 

The modem must be Hayes

 

®

 

–compatible and run at 1200, 2400, 4800, 9600, 

14000 or 19200 baud.

 

 

One internal or external modem connected to your computer

 

The modem must be Hayes

 

®

 

–compatible and run at 1200, 2400, 4800, 9600, 

14400 or 19200 baud.

 

 

Telephone Modem Adapter

 

The Telephone Modem Adapter (#6533) provides the connection between the 
data logger and the modem.

Summary of Contents for and Vantage Pro

















Reviews: