background image

7

Push 4 - Blower OFF (Default State)  

AIR  

No 

Light  

Push 1 - Blower ON (Full Speed) 

Push 2 - Blower ADJUSTABLE (Adjustable Speed)  

Push 3 - Blower OSCILLATING (Oscillating Speed)  

AIR  

Red 

Light 

Orange 

Light  

AIR  

AIR  

Green 

Light  

Note: If left on, this accessory will automatically switch off after 20 minutes. If the heater element is 

on, switching on this accessory may cause the heater to loadshed and switch off.This is to keep the 

total power load to a safe level. 

4.1 Adjustable Speed Mode (SPVSB only) 

If a Spa Power Variable-Speed Blower is fitted, the spa user has the ability to adjust the blower speed to any 

desired setting. The Up and Down buttons are used to set the desired blower speed. Note: If the blower is in 

Full Speed or Oscillating modes then pushing the Up or Down button will put it into Adjustable Speed mode 

and then adjust the speed.  

Step 1)  

Press Air Button 

twice

 to set Adjustable Speed Mode 

Step 2)  

Press Up 

 to 

increase 

speed of blower  

Step 3)  

Press Down 

 

 to 

decrease 

speed of blower  

5. LIGHT OPERATION

 

Your spa may have been fitted with either of two different LED lights; a Spa Power Coloured Light (SPCL) or 

a Spa Power Variable Coloured Light (SPVCL). The Spa Power Coloured Light is a single coloured light that 

is either on or off. The Spa Power Variable Coloured light is a light that has the ability to change between 12 

different colours and white (see below for user instructions).  

The multi-function Light Button 

  is used to turn the light on and off (SPCL) and select through 

the different operating modes of the Spa Power Variable Colour Light. Two short presses of the button 

will turn the Spa Power Coloured Light on and off or five short presses of the button will cycle the Spa 

PowerVariableColouredLight asfollows:  

 

Light Button  

Push 1 - Light ON   

(SPCL - On) (SPVCL Colour - White)  

Push 2 - Light ADJUST    (SPCL - Off) (SPVCL Adjustable Colour Mode)  

Push 3 - Light CYCLE SLOW   (SPVCL Cycle through colours - slowly)

Push 4 - Light CYCLE FAST    (SPVCL Cycle through colours - quickly)  

Push 5 - Light OFF   

(Default State)  

Note: This is a multi-function button which performs the following - 

1) Short presses of this button activate the light functions as detailed above. 

2) Holding this button will begin to increase the set temperature of the spa. 

3)  When a Spa Power Variable Speed Blower is fitted and is turned on this button increases the  

blowerspeed. 

5.1 Adjustable Colour Mode (SPVCL only)  

When the light is on, short presses of the Down button 

 will put the light into adjustable colour mode 

and then sequentially select through all the available colours. The last colour set in this mode will be remem-

bered the next time the light is used.  

AIR

  

Light turns  

to orange

Summary of Contents for SpaPOWER SP400P













Reviews: