background image

4

   H20 LED (24hr circulation pump fitted) 

   Theyellow H20lightindicatesifwaterispresentintheheater.IfnowaterisdetectedthentheLED will 

flash and the unit will not operate except to run the circulation pump to try to get water to the 

heater. If no water reaches the heater for one minute then an H20 error will occur. If this happens 

thenpushingthepumpbuttonwillrunthecirculationpumpforanotherminute. 

   Pump LED 

   The green Pump indicator light will appear on the touch pad whenever the pump is running, in both 

autoandmanualusemode.Ifthislightisflashing,thespaisinSleepMode. 

   Heat LED 

   The red Heater indicator light will appear on the touchpad whenever the heater element is on, 

in both auto and manual use mode. For safety the heater is always automatically controlled. 

Usuallyswitchingontheairbloweraccessorywillcausetheheater to switch off (loadshedding). This is in order 

to keep the total power load to a safe level. If this light is flashing the system has an error (see section 8). 

   Aux/Air LED 

   The Aux/Air indicator LED will appear on the touchpad whenever the Aux/Air button is pushed and 

conversly will disapear when the button is pushed again. Note: If the spa does not have a load connected 

to the controller the LED will still operate as described above.  

2. TEMPERATURE CONTROL

 

The Spa Power controller automatically controls the pump and heater to filter the water and maintain it at the 

desired temperature set by the user (see below). The user can leave the system to look after the spa and 

know it will be at the correct temperature when ever he or she wants to use it. 

2.1 Adjusting Set Temperature 

The Spa Power controller gives the user direct control of the pool temperature from the poolside control 

panel. Holding down the Up or Down button will adjust the temperature set point as shown on the digital 

readout. There is a slight delay before the buttons operate to reduce the risk of accidental adjustment. The 

pool temperature will be maintained very close to the set temperature.  

  

UP

   

Increase the set temperature by 0.5

o

C per beep (Max = 41.5

o

C) 

  

DOWN

   Decrease the set temperature by 0.5

o

C per beep (Min = 10.0

o

C) 

Default Display

 

The display normally shows the temperature set point, unless the optional in pool temperature sensor is fitted 

in which case the sensed water temperature is displayed. In either case the temperature set point will be 

displayed while being adjusted as describe dabove.  

2.2 Non-Default Display Value 

The non-default display value (either sensed water temperature 

or temperature set point) can be checked if necessary by 

pressing the Up &Down buttons simultaneously.  

2.3 Heating Mode Selection (24hr circ pump not fitted)  

In addition to the temperature setting the user can select the preferred heating mode. The two available 

heating modesare... 

1.  Demand Heating (displayed as Ht.d).This is the default setting in which the pump and heater will come on 

automaticallywheneverthetemperaturedropsslightlybelowthesetpoint. 

2.  FiltrationOnlyHeating(displayedasHt.F).In this mode the pump and heater will come on automatically no 

more than once per hour to filter and heat the water. This mode is provided as an option for those who 

prefer to limit the natural cycling of the system. 

Summary of Contents for SpaPOWER SP400P













Reviews: