manualshive.com logo in svg

Datron guardian II series, Operator'S Manual, Page: 45 / 47

Share
Download
Datron guardian II series Operator'S Manual Download Page 45

Analog/Digital Tone Pick List  

Tone pick lists are created in the PC Programmer. They are selected by accessing the main menu. 
Up to 32 transmit tones (CTCSS, DCS) and 32 digital NAC codes can be programmed into the 
radio. If one of these tones or codes is selected, the programmed tag name replaces the existing 
channel name. The use of a tone picklist provides a permanent change to the channel. 

To access these tones, the following options exist. For all of these, press the # key for a short 
duration (press and release). A tone or code is replaced by the desired number: 

•

 

Press # and single digit ID number. 

•

 

Press # and 2-digit ID number. 

•

 

Press # and 0 and single digit number. 

•

 

Press # and single or 2 digits and <

ENT

>. 

•

 

A special case of pressing # 00 is reserved for removing the CTCSS or DCS tone on 
analog channels. 

NO

 

TXSQ

 is displayed on the channel name. 

Note: 

If a channel is altered with the tone picklist that had a receive CTCSS or DCS tone 

programmed to it, that channel is automatically set to receive carrier squelch. 

Talk Group Picklist 

The talk group list applies only to digital channels. It can only be programmed by the PC 
Programmer or cloning. To access the list: 

1.

 

Press and hold the 

*

 key until the talkgroup list is displayed. If no list exists, 

EMPTY

 

is 

displayed. 

2.

 

Select the desired talkgroup, and press <

ENT

>. The talk group tag replaces the channel tag. 

The use of a talk group list provides a permanent change to the channel. 

Summary of Contents for guardian II series
















































Reviews:

No comments