manualshive.com logo in svg

Datex-Ohmeda S/5 M-ESTPR, Technical Reference Manual Slot

Share
Download
Datex-Ohmeda S/5 M-ESTPR Technical Reference Manual Slot Download Page 60

Datex-Ohmeda S/5 monitors

Document No. 800 1008-2

54

5.1

 

NIBP service menu

Service Data

Pressure 

shows measured pressure multiplied by 10.

Zero 

shows pressure at auto zeroing multiplied by 10 and changes b20 and -20 mmHg.

Absolute pressure is the sum of 

Pressure 

and 

Zero

.

Protect handle 

indicates hardware protection for EEPROM memory. It should be ON all the time in

normal operation. If it is OFF data can not be read from or written to EEPROM, only the calibration

protection can be set or reset by software. It can be turned to OFF by turning the toggle switch to the

right at the bottom of the module, which also enables 

Protection ON/OFF

 menu selection in the

calibration menu.

Calibr. prot. 

shows software calibration protection and it should be OFF to enable calibration.

+15 V power 

indicates the condition of the supply v15 Vdirty for the pump and valves. It

exists (ON) or not (OFF) depending on service menu function. The supply voltage can be turned on

by selecting the previous Menu and then the desired menu again.

AD0 

to 

AD7 

show the values of each eight channels of A/D converter.

Timeouts 

is a cumulative number that indicates how many times the module has not responded to

the monitor’s inquiry. 

Bad checksums 

is a cumulative number that indicates how many times

communication from the module to monitor broke down.

Bad c-s by mod

 is a cumulative number that indicates how many communication errors the

module has detected.

The monitor starts counting these items at power up and resets to zero at power off. The nonzero

values do not indicate a failure, but the continuous counting (more than 50 per second) indicates

either serial communication failure, or module not in place. Also other modules can cause

communication errors that cause these numbers rise.

RAM 

indicates the state of the RAM memory.

ROM 

indicates whether the checksum in the EPROM is in accordance with the one the software has

calculated.

Summary of Contents for S/5 M-ESTPR

























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands