Datex-Ohmeda S/5 M-ESTPR Technical Reference Manual Slot Download Page 50

Page: 50 / 88

Datex-Ohmeda S/5 monitors

Document No. 800 1008-2

TROUBLE

CAUSE

TREATMENT

Cuff loose-message

1. Hose and/or cuff not connected.

1. Connect the hose and the cuff.

2. Hose and cuff connected.

Reasons:

−

cuff loosely wrapped

−

tighten the cuff

−

leakage in cuff or hose

−

replace cuff/hose

−

leakage inside module

−

check internal tubing and air

chamber, and fix if necessary

−

pump does not work

−

check pump connector; if OK, replace

pump

−

no pulses during the last three

measurements

−

check cuff positioning

Air leakage-message

1. Hose or cuff leaking. Reasons:

1. Replace cuff

−

cuff damaged

−

replace cuff

−

cuff connector damaged

−

replace cuff connector (if the fault is

in hose connector,)

−

O-ring damaged or missing

−

replace O-ring

−

hose double connector

damaged

−

replace hose

2. Hose and cuff OK. Reasons:

2. Connect or replace tube

−

leakage inside the module

−

replace the whole tubing

−

tube disconnected or damaged

−

fix connections

−

air chamber leaking

−

tubes or valve(s) damaged

−

replace tubes/valve(s)

Unable to measure Sys-

message

Systolic blood pressure probably

higher than the maximum inflation

pressure.

Automatic retrial with increased

pressure.

Summary of Contents for S/5 M-ESTPR

























































































Search results

Summary of Contents for S/5 M-ESTPR

Reviews:

Brands by name

Popular brands

Datex-Ohmeda S/5 M-ESTPR, Technical Reference Manual Slot

Search results

Summary of Contents for S/5 M-ESTPR

Reviews:

Brands by name

Popular brands