manualshive.com logo in svg

Datex-Ohmeda S/5 M-ESTPR, Technical Reference Manual Slot

Share
Download
Datex-Ohmeda S/5 M-ESTPR Technical Reference Manual Slot Download Page 17

S/5 Hemodynamic modules

Document No. 800 1008-2

11

boards, attached to the front panel of the module. The front panel has six connectors and four keys.

The connectors are two for temperature measurement, two for invasive blood pressure

measurement, one for ECG, and one for SpO

2

 measurement. The keys are for ECG lead, Start

Wedge, P1 zero, and P2 zero.
In 

M-ETPR module

,

 

there are two small boards, the ECG input board and the 2P input board

attached to the front panel of the module. The front panel has five connectors and four keys. The

connectors are two for temperature measurement, two for invasive blood pressure measurement,

and one for ECG

 

measurement. The keys are for ECG lead, Start Wedge, P1 zero, and P2 zero.

In 

M-ESTR module

, there are two small boards: the S input board and the ECG input board,

attached to the front panel of the module. The front panel has four connectors and one key. The

connectors are two for temperature measurement, one for ECG, and one for SpO

2

 measurement.

The key is for ECG lead select.
NOTE: M-ESTP rev. 03, M-ETP rev. 02 and M-EST rev. 02 and all earlier revisions have separate T

and SP input boards.

2.2.2

 

M-NE12STPR/-NE12STR/-NE12TPR/-NESTPR/-NESTR/-NETPR modules

Figure 4

Front panel of M-NESTPR

The 

M-NESTPR, M-NETPR, and M-NESTR

 

modules 

contain three main PC boards, the STP board,

the ECG board, and the NIBP board. They work independently. Each of these has their own

processor and software EPROM.
The 

M-NE12STPR, M-NE12TPR, and M-NE12STR

 contain three main PC boards, The STP board,

the ECG board and the NIBP board. They work independently. Each of them has their own

processor. The STP board and NIBP board have software EPROM. In the ECG board the software is

in flash memory. The STP and NIBP boards are the same as in M-NESTPR module but the ECG

board and ECG input board are different.
In 

M-NESTPR module

, there are two small boards, the SP input and the ECG input board attached

to the front panel of the module. The front panel has seven connectors and four keys. The

connectors are two for temperature measurement, two for invasive blood pressure measurement,

one for ECG, one for NIBP, and one for SpO

2

 measurement. The keys are for NIBP Auto On/Off,

NIBP Start/Cancel, P1 zero, and P2 zero. The structure of 

M-NE12STPR

 is similar except the ECG

board and ECG input board are different.

T2

P1

P2

T1

NIBP

ECG+
Resp

Auto

On/Off

Zero

P1

Zero

P2

Start

Cancel

SpO

2

Summary of Contents for S/5 M-ESTPR

























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands