manualshive.com logo in svg

Datex-Ohmeda S/5 M-ESTPR, Technical Reference Manual Slot

Share
Download
Datex-Ohmeda S/5 M-ESTPR Technical Reference Manual Slot Download Page 42

Datex-Ohmeda S/5 monitors

Document No. 800 1008-2

36

29.

 

Check the NIBP tubing system for leakages.

Select 

Calibrations

 from the NIBP service menu.

Connect the pressure manometer to the NIBP module cuff connector. Start the active leak

test from the menu by pressing the ComWheel. The module pumps a pressure of about 265

mmHg and then the pump stops.

Wait for 15 seconds for the pressure to stabilize then check that the pressure does not drop

more than 5 mmHg per one minute. Release the pressure by pressing the ComWheel once

more.

?

30.

 

Calibration check.

Disconnect the pressure manometer. Select 

Calibrations

 and then highlight 

Calibration

Check

. Press the ComWheel and take down the zero offset values for both pressure

transducers, B1 and B2. The values should be within ±10 mmHg.

Connect the pressure manometer to the cuff connector and check the calibration with

pressures 100 mmHg, 200 mmHg and 260 mmHg. The zero offset value must be added to

the displayed pressure value in order to determine the real pressure.

Recalibrate the NIBP measurement according to the instructions in the chapter 3.4

Adjustment and calibration, 

Calibration

, if necessary. Remember to set the calibration

protection back on after the calibration.

?

31.

 

Check the watchdog timer activation pressure.

Select 

Pneumatics

 from the NIBP service menu.

Keep the pressure manometer connected to the cuff connector. Pump up the pressure very

slowly and note the value on the manometer when your hear a signal from the loudspeaker.

The pressure at where the watchdog timer should activate with an audible signal is

7.5 mmHg (5...10 mmHg). Adjust the limit with the trimmer on the NIBP board, if necessary.

?

Summary of Contents for S/5 M-ESTPR

























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands