background image

EN

Dateq BCS70 Manual

Operating instructions

21

Setup-mode

The settings on the mixer unit can be changed using the Setup mode. This applies in particular
to the settings w hich used to have to be made w ith jumpers on all modules. The great
advantage is, of course, that the user can make changes in the use of the console quickly
w ithout having to unscrew  the modules.

The Setup mode is activated by pressing the very noticeable red SETUP button. The LED
under this button and the ON and OFF button on all modules start to flash. The LED in the AIR
button on the CR selector panel flashes. BUTTON START appears next to this in blue. This
indicates that those channels that must w ork w ith button start can now  be set. Should a
channel w ork w ith button start? If so, press the ON button on the channel concerned. Press
the channel's OFF button if that channel should be set as fader start.

The follow ing settings can be made in the same w ay (see blue print):

BUTTON START

Select ON if a channel should be sw itched on and off w ith the ON
and OFF button. Select OFF if the channel should be sw itched on and
off w ith the fader.

MASTER CUE

Select w hether a channel automatically sets the Control Room
selection on CUE w hen CUE is pressed (select ON), or w hether this
must be done manually (select OFF).

DJ MODE

If a channel is for an announcer w ho is also the technician, select ON.
The Control Room speakers w ill then automatically be muted if this
channel is open. For the other non-DJ channels select OFF.

COUGH > COM

If the external mute on a microphone or line module is active (by
pressing the cough / talk button), the module automatically sw itches to
CUE (if OFF is selected) or to COM (if ON is selected). In this last case,
any 'coughing' is to the COM bus. In this w ay one can, for example,
speak directly to the director, instead of to the technician.

EXT MUTE

Select ON if the channel must be muted if an external sw itch is
pressed (cough / talk button). Select OFF if the external sw itch is used
as a remote CUE sw itch (positioned, for example, near a turn-table to
set the mixer unit to CUE by remote control).

ONAIR 1

Select ON if a module should be part of on-air group 1, select OFF if it
should not be part of this group.

ONAIR 2

Select ON if a module should be part of on-air group 2, select OFF if it
should not be part of this group.

RES

Reserved for a BCS81 clock / timer (if installed). Select ON if a module
must be able to start and stop the timer w hen the module is turned on
and off. Select OFF if the module may not start or stop the timer.

NORMAL / SPLIT

During CUE the technician can choose w hether the signal from the
Control Room selector panel comes to the Phones output normally
(select N) or as a split signal (select S). In this last case, the PGM
signal goes to one earphone and the CR signal selected to the other
earphone of the headphones.

GST 1 COM

To route Guest 1 to the COM bus, the mixer unit must know  w hich
module(s) belong to Guest 1. Select ON on these modules (thus
making a Guest 1 group!), OFF on the other modules.

GST 2 COM

The same for Guest(s) 2.

ANN COM

The same for the Announcer(s).

Summary of Contents for BCS70

































Reviews: