manualshive.com logo in svg

Dataradio Paragon, Technical Manual

Share
Download
Dataradio Paragon Technical Manual Download Page 4

 

120 20170-204a

iv

Paragon

PD

 Technical Manual

6.3.3

Channel Selection via DIP Switches ..................................................................................................... 45

6.4

S

ERIES 

II R

ADIO 

T

UNING

................................................................................................................................ 46

6.4.1

Test Equipment...................................................................................................................................... 46

6.4.2

Receiver module (T885, T855 & T835)................................................................................................. 46

6.4.2.1

Initial Setup ...................................................................................................................................................46

6.4.2.2

Synthesizer Alignment ..................................................................................................................................47

6.4.2.3

Front-End Alignment ....................................................................................................................................47

6.4.2.4

SINAD and Linearity Check .........................................................................................................................47

6.4.2.5

RSSI Adjustment (T885 and T855)...............................................................................................................48

6.4.2.6

RSSI Adjustment (VHF: T835).....................................................................................................................49

6.4.3

Exciter Module (T881,T857 or T837) ................................................................................................... 50

6.4.3.1

Initial Setup ...................................................................................................................................................50

6.4.3.2

Synthesizer Alignment ..................................................................................................................................50

6.4.3.3

TX Frequency Error Adjustment ...................................................................................................................50

6.4.3.4

Low-Frequency Balance Adjustment ............................................................................................................51

6.4.3.5

Exciter Power Output ....................................................................................................................................52

6.4.4

Power Amplifier Module (T889 (800-870 MHz only), T859 or T839) .................................................. 52

6.4.4.1

Power Amplifier Power Output .....................................................................................................................52

6.4.4.2

Forward Power Alarm Level .........................................................................................................................52

6.4.4.3

Reverse Power Alarm Level (Optional) ........................................................................................................53

6.4.4.4

Tait T859 (UHF) Standard Tuning Procedure...............................................................................................53

6.4.4.5

Tait T859 Tuning for Best Efficiency............................................................................................................53

6.4.5

(TPL) LMS series Power amplifier (PA8-2BF-LMS) (806-960 MHz)................................................... 54

6.4.5.1

Power Output alignment (from TPL Communications).................................................................................54

6.4.5.2

Forward Power Alarm Level .........................................................................................................................54

6.4.5.3

Amplifier Activation......................................................................................................................................54

6.4.5.4

RF Input (Relative Reading) .........................................................................................................................54

6.4.5.5

Forward Power meter calibration ..................................................................................................................54

6.4.5.6

Reverse Power meter calibration ...................................................................................................................55

6.4.5.7

Reverse Power Alarm Level ..........................................................................................................................55

7.

SPECIFICATIONS .......................................................................................................................................... 63

A

PPENDIX 

1 - P

ARAGON

PD

 

D

EVIATION ADJUST

........................................................................................................ 62

F

IGURE 

1 - T

YPICAL RADIO AND POWER SUPPLY ASSEMBLIES

, 

FRONT VIEW

................................................................... 5

F

IGURE 

2 - BDLC

PD

, 

FRONT VIEW

................................................................................................................................. 5

F

IGURE 

3 - T

YPICAL RADIO AND POWER SUPPLIES ASSEMBLY

, 

REAR VIEW

..................................................................... 6

F

IGURE 

4 - BDLC

PD

, 

REAR VIEW

................................................................................................................................... 6

F

IGURE 

5 - BDLC

PD

’

S REAR CONNECTION

, 

SWITCH AND FUSE

....................................................................................... 8

F

IGURE 

6 - R

ECEIVER MODULE FRONT PANEL

................................................................................................................ 9

F

IGURE 

7 - E

XCITER MODULE

, 

FRONT PANEL

............................................................................................................... 10

F

IGURE 

8 - P

OWER 

A

MP MODULE

, 

FRONT PANEL

......................................................................................................... 10

F

IGURE 

9 - S

PEAKER PANEL

......................................................................................................................................... 11

F

IGURE 

10 - D

UAL 

P

OWER 

S

UPPLY REAR CONNECTIONS

.............................................................................................. 11

F

IGURE 

11 - BDLC

PD

 MEMBRANE SWITCHES

............................................................................................................... 12

F

IGURE 

12 - RF 

INDICATORS

........................................................................................................................................ 14

F

IGURE 

13 - RS-232 P

ORT 

LED 

INDICATORS

.............................................................................................................. 15

F

IGURE 

14 - ALARMS LED 

INDICATORS

.................................................................................................................... 15

F

IGURE 

15 - BDLC

PD

 

Y 

CABLE AND PINOUT

............................................................................................................... 17

F

IGURE 

16 - S

ERIES 

I R

ECEIVER 

S

YSTEM 

I

NFORMATION

.............................................................................................. 31

F

IGURE 

17 - S

ERIES 

I C

HANNEL 

I

NFORMATION

............................................................................................................ 32

F

IGURE 

18 - C

HANNEL 

S

ELECTION VIA INTERNAL 

DIP 

SWITCHES

................................................................................ 34

F

IGURE 

19 - T885 R

ECEIVER TUNING CONTROL LOCATION

.......................................................................................... 40

F

IGURE 

20 - T881 E

XCITER TUNING CONTROLS LOCATION

.......................................................................................... 41

F

IGURE 

21 - R

ECEIVER 

S

YSTEM 

I

NFORMATION

............................................................................................................ 43

Summary of Contents for Paragon









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands